manualshive.com logo in svg

Mercury 3.0L Carbureted Alpha, Installation Manual

Share
Download
Mercury 3.0L Carbureted Alpha Installation Manual Download Page 116

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 116 of 137

90-860172011

4. Push down on T-handle to force the blue drain hoses below their connection points to

the block.

76244

a

a -

Connection Points

5. Ensure water is draining from both blue drain hoses. If water is not draining from one

or both blue drain hoses, go to “Clearing Clogged Blue Drain Hoses.”

6. Leave blue drain hoses disconnected until all water has drained from engine.

7. Pull T-handle until the quick connect fittings “

a

” on the blue drain hoses are within reach.

76244

a

a -

Quick Connect Fittings

8. Install quick connect fittings on the bracket. Pull on the blue drain hoses to ensure they

are firmly connected.

9. Push down on handle and move into the slot on the bracket.

10. Turn off bilge pump.

IMPORTANT: The next time the engine is started, visually inspect that the blue drain
hoses are connected and not leaking.

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands