manualshive.com logo in svg

Mercury 3.0L Carbureted Alpha, Installation Manual

Share
Download
Mercury 3.0L Carbureted Alpha Installation Manual Download Page 98

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 98 of 137

90-860172011

Predelivery Preparation

Once the power package installation is complete, the following final steps should be taken
to prepare power package for delivery to the customer. It is the boat manufacturer’s
responsibility to perform these procedures, or to make arrangement with the dealer to have
these procedures completed.

Power Steering Fluid

IMPORTANT: Use only specified lubricant.

CAUTION

DO NOT RUN POWER STEERING DRY or pump will be damaged.

1. Position sterndrive unit so that it is straight back.

2. Remove fill cap from power steering pump and check fluid level using dipstick. Add

fluid as required.

NOTE: Be prepared to add fluid to pump when first starting engine.

71672

76859

a

a

b

a -

Fill Cap

b -

Dipstick

Description

Where Used

Part Number

Power Trim and Steering Fluid

92-90100A12

Dexron III - Automatic
Transmission Fluid

Power Steering Pump

Obtain Locally

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands