Mercury 3.0L Carbureted Alpha Installation Manual Download Page 17

Page: 17 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 17 of 137

TRANSOM MOUNTED

1. Seal the inside edges of the 1-1/2 in. (38 mm) hole hose fitting.

2. Ensure that the hose fitting and plastic plug are in place and threads have been sealed

prior to tightening each securely.

Description

Where Used

Part Number

Hose Fitting Threads

Loctite 592 PST

Plastic Plug Threads

Obtain Locally

Silicone Sealant Or Equivalent

Screw Shaft

NOTE: Use a sharp knife or wood chisel to remove excess plastic plug material so that plug
is flush with pickup casting.

3. Position one flat washer and one rubber O-ring on each 5/16 in. x 4 in. (102 mm) long,

round head screw. Coat each screw shaft with sealant.

4. Place new gasket on pickup housing and hold pickup in place on transom. Install four

round head screws (with washers and O-rings in place) into pickup mounting holes and
through drilled 21/64 in. (8 mm) holes in transom.

72640

a -

Hose Fitting

b -

Nut (4)

c -

Gasket

d -

O-ring (4)

e -

Washer (4)

f -

Screw (4)

g -

Plastic Pug

h -

Pickup

i -

Screen

j -

Screw (2)

Summary of Contents for 3.0L Carbureted Alpha










































































































































Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands

Mercury 3.0L Carbureted Alpha, Installation Manual

Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands