Mercury 3.0L Carbureted Alpha Installation Manual Download Page 10

Page: 10 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 10 of 137

90-860172011

Boat Construction

Transom Thickness and Surface

IMPORTANT: Transom thickness and surface plane (flatness) must be controlled
where the sterndrive unit mounts.

Transom Specifications

Thickness

Between 2 - 2-1/4 in. (51 - 57 mm) for 8 in. (203 mm) to either
side of the vertical centerline

Parallelism

Inner and outer surfaces must be parallel within 1/8 in. (3 mm)

Flatness

Transom surfaces in area where transom assembly will be
mounted (includes vertical as well as horizontal dimensions):

Inner Surface – Flat within1/8 in. (3 mm)

Outer Surface – Flat within1/16 in. (2 mm)

Angle

10 -16 Degrees

22170

72700

a -

Transom Thickness

b -

Inner Surface

c -

Outer Surface

d -

Transom Plate Coverage

e -

Transom Angle

70004

75479

a -

Measuring Thickness

b -

Measuring Flatness

c -

Suitable Mandrel To Check For Uniform Transom Thickness

Summary of Contents for 3.0L Carbureted Alpha










































































































































Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands

Mercury 3.0L Carbureted Alpha, Installation Manual

Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands