Mercury 3.0L Carbureted Alpha Installation Manual Download Page 30

Page: 30 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 30 of 137

90-860172011

MANUAL STEERING

1. Inspect bushings for debris. Lubricate bushings with Special Lubricant 101.

22946

Manual Steering

a -

Bushings

b -

Special Lubricant 101

2. Remove shipping hardware.

3. Remove upper and lower pivot bolts and ensure threads are well lubricated with Special

Lubricant 101.

NOTICE to INSTALLER

Refer to “Installation Requirements - Steering Helm and Cable” for steering cable
selection and coupler nut locking requirements.

4. Install steering assembly as follows:

a. Position steering assembly so that pivot bolts will enter bushings in pivot block or

power steering control valve.

b. Install upper and lower pivot bolts along with tab washers. Ensure that tab washer

tangs straddle the ridge on inner transom plate.

c. Turn pivot bolts all the way in by hand to ensure proper alignment.

d. Ensure steering assembly pivots freely.

5. Torque pivot bolts to 25 lb-ft (34 Nm). Bend washer tabs against corresponding flats on

bolt heads.

22033

Manual Steering

a -

Tab Washers

b -

Ridge

c -

Pivot Bolts

NOTE: It may be necessary to tighten further to align flats on pivot bolt with tabs on tab
washer.

Summary of Contents for 3.0L Carbureted Alpha










































































































































Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands

Mercury 3.0L Carbureted Alpha, Installation Manual

Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands