background image

It is of vital importance, before attempting to operate 
your  engine,  to  read  the  general 

'SAFETY 

INSTRUCTIONS  AND  WARNINGS'  section  on 
pages 2-5 of this booklet and to strictly adhere to the 
advice contained therein.

Also,  please  study  the  entire  contents  of  this 
instruction  manual,  so  as  to  familiarize  yourself 
with the controls and other features of the engine.

Keep these instructions in a safe place so that you 
may readily refer to them whenever necessary.

It  is  suggested  that  any  instructions  supplied  with 
the  vehicle,  radio  control  equipment,  etc.,  are 
accessible for checking at the same time.

JAPAN

1

2-5

6-7

   8

9

10-11

12

13-15

16

17

18-19

20-26

27-30

31-34

35-37

38-45

46-49

  

50-52

53-56

CONTENTS

SAFETY INSTRUCTIONS AND 
WARNINGS ABOUT YOUR O.S. ENGINE

ENGINE CONSTRUCTION, NOTES WHEN
APPLYING AN ELECTRIC STARTER

INSTRUCTIONS

BASIC ENGINE PARTS

TOOLS, ACCESSORIES, etc.

STANDARD ACCESSORIES

CARBURETOR CONTROLS,
INSTALLATION OF THE CARBURETOR

NOTES CONCERNING THE RECOIL STARTER

GLOWPLUG

ENGINE INSTALLATION

STARTING THE ENGINE &
RUNNING-IN ('Breaking-in)

FINAL ADJUSTMENT

TROUBLE SHOOTING

CARE AND MAINTENANCE

EXPLODED ENGINES  VIEWS &
PARTS LIST

CARBURETOR EXPLODED VIEW  & 
PARTS LIST

O.S. GENUINE PARTS & ACCESSORIES

THREE VIEW DRAWING

Summary of Contents for MAX-12TG






























Reviews: