Lucent Technologies CAJUN M770 User Manual Download Page 56

Page: 56 / 266

Chapter 5

Managing Physical Ports

Cajun M770 ATM Switch User’s Guide

To display information for all physical ports, enter the

pport show

command.

Note:

In the above Table, Port 0 is the CPU port and Port 16 is the Backplane port.

Command:

M15-155s8:/>pport show

Output:

Physical Port Information

Port

Admin Oper

Speed

Framing VPI

VCI

State State Kbps

Mode

Range

8.0

---

[0..0] [0..1023]

8.1

Down

155520 Sonet

[0..7] [0..1023]

8.2

Down

155520 Sonet

[0..7] [0..1023]

8.3

Down

155520 Sonet

[0..7] [0..1023]

8.4

Down

155520 Sonet

[0..7] [0..1023]

8.5

Down

155520 Sonet

[0..7] [0..1023]

8.6

Down

155520 Sonet

[0..7] [0..1023]

8.7

Down

155520 Sonet

[0..7] [0..1023]

8.8

Down

155520 Sonet

[0..7] [0..1023]

8.9

155520 Sonet

[0..7] [0..1023]

8.10

Down

155520 Sonet

[0..7] [0..1023]

8.11

Down

155520 Sonet

[0..7] [0..1023]

8.12

Down

155520 Sonet

[0..7] [0..1023]

8.13

Down

155520 Sonet

[0..7] [0..1023]

8.14

Down

155520 Sonet

[0..7] [0..1023]

8.15

Down

155520 Sonet

[0..7] [0..1023]

8.16

---

[0..15][0..65535]

Port

Cell

Payload

Media

Mode

Scrambling

Type

8.0

Unassigned

---

8.1

Unassigned

MMF

8.2

Unassigned

MMF

8.3

Unassigned

MMF

8.4

Unassigned

MMF

8.5

Unassigned

MMF

8.6

Unassigned

MMF

8.7

Unassigned

MMF

8.8

Unassigned

MMF

8.9

Unassigned

MMF

8.10

Unassigned

MMF

8.11

Unassigned

MMF

8.12

Unassigned

MMF

8.13

Unassigned

MMF

8.14

Unassigned

MMF

8.15

Unassigned

MMF

8.16

Unassigned

Off

---

Summary of Contents for CAJUN M770











































































































































































































































































Search results

Summary of Contents for CAJUN M770

Reviews:

Related manuals for CAJUN M770

Brands by name

Popular brands

Lucent Technologies CAJUN M770, User Manual

Search results

Summary of Contents for CAJUN M770

Reviews:

Related manuals for CAJUN M770

Brands by name

Popular brands