Lucent Technologies CAJUN M770 User Manual Download Page 236 | Manualshive

Page: 236 / 266

background image

Appendix B

Using BOOT Loader

218

Cajun M770 ATM Switch User’s Guide

From the BOOT MENU, you can view the current default BOOT Loader image that
is stored in flash memory. You can execute this image file or select the secondary
BOOT Loader image. If the secondary image is selected then this will become the
new default BOOT Loader image when the switch is next booted.

The last two options on the BOOT MENU, enable you to download a BOOT Loader
image on to the M770 ATM Switch via XMODEM at either 9600 Baud or 38400
Baud.

Note:

The download options should only be used in an emergency since all files and

configuration on the M770 ATM Switch will be wiped.

«
...
234
235
236
237
238
...
»

Summary of Contents for CAJUN M770











































































































































































































































































Reviews:

No comments

Related manuals for CAJUN M770

TokenLink Velocity 3C319

Brand: 3Com Pages: 2

Brand: i-MO Pages: 58

Device Server UDS 10

Brand: Lantronix Pages: 8

Brand: Watchguard Pages: 39

Brand: H3C Pages: 26

Brand: Tripp Lite Pages: 3

Brand: TP-Link Pages: 176

Brand: Hamlet Pages: 122

IP-Logic ZIG-IPPRO-RX

Brand: Zigen Pages: 4

Brand: Neousys Technology Pages: 39

Brand: e+p Pages: 2

Brand: Eneo Pages: 49

SA-REP-ETHERLINK_II-1DA-PL

Brand: S-Access Pages: 106

Brand: Allied Telesis Pages: 2

Brand: Hornington Pages: 8

Brand: ADF Web Pages: 20

Brand: Tripp Lite Pages: 2

Brand: D-Link Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands