Lucent Technologies CAJUN M770 User Manual Download Page 103

Page: 103 / 266

Chapter 6

Managing Virtual Ports

Cajun M770 ATM Switch User’s Guide

Type

The type of connection.
PP:

Point-to-Point SVC.

PMP:

Point-to-Multipoint SVC.

PVC:PP:

Point-to-Point PVC.

RES:

Reserved circuit.

DD_802.5:

LANE Data Direct Token-Ring VC

DD_802.3:

LANE Data Direct Ethernet VC

MC_802.5:

LANE Multicast Token-Ring VC

MC_802.3:

LANE Multicast Ethernet VC

CONTROL:

LANE Control VC

LES_MESH: Distributed LES SVC mesh
BUS_MESH: Distributed BUS SVC mesh
DIAGNSTIC: Diagnostic
ILMI:

ILMI

SIG:

Signalling.

Table 6.7

Output from the vport connections command (Continued)

Field

Description

Summary of Contents for CAJUN M770











































































































































































































































































Search results

Summary of Contents for CAJUN M770

Reviews:

Related manuals for CAJUN M770

Brands by name

Popular brands

Lucent Technologies CAJUN M770, User Manual

Search results

Summary of Contents for CAJUN M770

Reviews:

Related manuals for CAJUN M770

Brands by name

Popular brands