Lenovo ThinkStation P330 User Manual Download Page 94

Page: 94 / 134

b. Follow the following sequence to loosen the four screws that secure the heat-sink-and-fan assembly

to the system board:

• Partially loosen screw

, fully loosen screw

, and then fully loosen screw

• Partially loosen screw

, fully loosen screw

, and then fully loosen screw

Note:

Carefully loosen the four screws to avoid any possible damage to the system board. The four

screws cannot be removed from the heat-sink-and-fan assembly.

Figure 105. Removing the heat-sink-and-fan assembly

c. Lift the failing heat-sink-and-fan assembly off the system board.

Notes:

• You might have to gently twist the heat-sink-and-fan assembly to free it from the microprocessor.

• Do not touch the thermal grease while handling the heat-sink-and-fan assembly.

4. To install the heat-sink-and-fan assembly, do the following:

a. Apply appropriate amount of thermal grease to the new heat-sink-and-fan assembly.

b. Position the heat-sink-and-fan assembly on the system board. Ensure that the four screws are

aligned with the holes in the system board.

Note:

Ensure that the heat-sink-and-fan assembly cable is toward the microprocessor fan connector

on the system board.

c. Follow the following sequence to tighten the four screws to secure the new heat-sink-and-fan

assembly. Do not over-tighten the screws.

• Partially tighten screw

, fully tighten screw

, and then fully tighten screw

• Partially tighten screw

, fully tighten screw

, and then fully tighten screw

P330 User Guide

Summary of Contents for ThinkStation P330







































































































































Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands

Lenovo ThinkStation P330, User Manual

Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands