Lenovo ThinkStation P330 User Manual Download Page 128 | Manualshive

Page: 128 / 134

background image

This product has been tested and found to comply with the limits for Class B equipment according to
European Standards harmonized in the Directives in compliance. The Class B requirements for equipment
are intended to offer adequate protection to broadcast services within residential environments.

EU ErP (EcoDesign) Directive (2009/125/EC) - external power adapters (Regulation (EU) 2019/1782)

Lenovo products are designed to work with a range of compatible power adapters. Access

www.lenovo.com/us/en/compliance/eu-doc

to view the compatible power adapters. For the detailed power

adapter specifications for your computer, go to

https://support.lenovo.com

German Class B compliance statement

Hinweis zur Einhaltung der Klasse B zur elektromagnetischen Verträglichkeit

Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie zur elektromagnetischen
Verträglichkeit Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-
Mitgliedsstaaten und hält die Grenzwerte der Klasse B der Norm gemäß Richtlinie.

Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu
betreiben. Des Weiteren dürfen auch nur von der Lenovo empfohlene Kabel angeschlossen werden. Lenovo
übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne
Zustimmung der Lenovo verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne
Empfehlung der Lenovo gesteckt/eingebaut werden.

Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von
Betriebsmitteln, EMVG vom 20. Juli 2007 (früher Gesetz über die elektromagnetische Verträglichkeit von
Geräten), bzw. der EU Richtlinie 2014/30/EU, der EU Richtlinie 2014/53/EU Artikel 3.1b), für Geräte der
Klasse B.

Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen -
CE - zu führen. Verantwortlich für die Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo
(Deutschland) GmbH, Meitnerstr. 9, D-70563 Stuttgart.

Japan VCCI Class B compliance statement

Japan compliance statement for products which connect to the power
mains with rated current less than or equal to 20 A per phase

Japan notice for ac power cord

The ac power cord shipped with your product can be used only for this specific product. Do not use the ac
power cord for other devices.

122

P330 User Guide

«
...
126
127
128
129
130
...
»

Summary of Contents for ThinkStation P330







































































































































Reviews:

No comments

Related manuals for ThinkStation P330

Personal Computer

Brand: IBM Pages: 318

Compute Stick STK1A32SC

Brand: Intel Pages: 11

Brand: Advantech Pages: 19

Master MP1-11TGS Series

Brand: MiTAC Pages: 2

Brand: Fairlight Pages: 439

Brand: Hitachi Pages: 123

Brand: Hitachi Pages: 194

Brand: Hitachi Pages: 197

Brand: Hitachi Pages: 227

Brand: Hitachi Pages: 1153

Brand: Winmate Pages: 60

Brand: Winmate Pages: 92

Brand: Vizio Pages: 36

Brand: National Instruments Pages: 37

Brand: Canon Pages: 186

Brand: Franklin Computer Pages: 108

Brand: POSIFLEX Pages: 19

Brand: Shuttle Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands