Lenovo ThinkStation P330 User Manual Download Page 75

Page: 75 / 134

b. To install a new storage drive into the bracket, flex the bracket and align pin

, pin

, and pin

on the bracket with the corresponding holes in the storage drive. Do not touch the circuit board

on the storage drive.

Figure 79. Installing the storage drive into the bracket

c. Align the three plastic tabs on the left side of the storage drive with the corresponding holes in the

drive bay assembly. Then pivot the storage drive inward until it snaps into position.

Figure 80. Installing the storage-drive

d. Connect the signal cable and the power cable to the new storage drive.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

Chapter 6

Hardware removal and installation

Summary of Contents for ThinkStation P330







































































































































Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands

Lenovo ThinkStation P330, User Manual

Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands