Lenovo ThinkStation P330 User Manual Download Page 7

Page: 7 / 134

Chapter 1. Meet your computer

Front view

Note:

The computer hardware might look slightly different from the illustration.

Figure 1. Front connectors, controls, and indicators

Power button

Power indicator

Storage-drive activity indicator

SD card slot (available on some models)

Microphone connector

Headset connector

USB-C connector

USB 3.1 connectors Gen 1 (2)

USB 3.1 connectors Gen 2 (2)

Slim optical-drive eject button (available on some

models)

Flex bay (available on some models)

Power button

Press the power button to turn on your computer. If your computer is unresponsive, you can turn off the
computer by pressing and holding the power button for four or more seconds.

Power indicator

When the power indicator is on, the computer is turned on.

Summary of Contents for ThinkStation P330







































































































































Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands

Lenovo ThinkStation P330, User Manual

Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands