Lenovo ThinkStation P330 User Manual Download Page 12 | Manualshive

Page: 12 / 134

background image

When you remove or install an internal storage drive, note the type and size of the drive that each bay
supports and correctly connect the required cables. Refer to the appropriate section in Chapter 6 “Hardware
removal and installation” on page 23 for instructions on how to remove or install internal storage drives for
your computer.

The following illustration shows the locations of the storage drives.

Note:

The computer hardware might look slightly different from the illustration.

Figure 3. Storage-drive bay locations

1

Type-1 storage-drive cage

2

SD card slot (available on some models)

3

Flex bay (available on some models)

4

M.2 solid-state drive slot

5

Type-2 storage-drive cage

6

Type-1 storage-drive bay

7

PCIe card slots (3)

1

Type-1 storage-drive cage

6

P330 User Guide

«
...
10
11
12
13
14
...
»

Summary of Contents for ThinkStation P330







































































































































Reviews:

No comments

Related manuals for ThinkStation P330

POWERMATE ES 5250 - S

Brand: NEC Pages: 18

POWERMATE VT 300 RELEASE NOTES

Brand: NEC Pages: 16

POWERMATE CT 815 - RELEASE NOTES

Brand: NEC Pages: 155

Brand: NEC Pages: 6

POWERMATE ES Series

Brand: NEC Pages: 132

POWERMATE ES Series

Brand: NEC Pages: 8

Brand: NEC Pages: 167

Brand: NEC Pages: 1

StorageWorks 4300

Brand: Compaq Pages: 21

IntelliStation Z Pro 6221

Brand: IBM Pages: 110

Brand: Moxa Technologies Pages: 19

FocusPRO 6000 Series

Brand: Honeywell Pages: 64

X-Superteam XPS-100

Brand: Honeywell Pages: 40

Brand: Honeywell Pages: 69

Brand: Honeywell Pages: 39

Brand: Honeywell Pages: 78

Brand: Honeywell Pages: 39

Brand: Honeywell Pages: 133

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands