Lenovo ThinkStation P330 User Manual Download Page 52

Page: 52 / 134

• Front-access storage enclosure

Note:

The following instructions on how to remove or install an flex storage enclosure also apply to other

supported devices in the flex bay.

To remove or install an flex storage enclosure, do the following:

1. Prepare your computer. See “Preparing your computer” on page 24.

2. Locate the flex bay.

3. To remove the flex storage enclosure, do the following:

a. Disconnect the signal cable and the power cable from the rear of the flex storage enclosure.

Note:

If you are removing other supported devices from the flex bay, disconnect any additional

cables first.

b. Press the tab downward as shown and push the rear of the flex storage enclosure simultaneously to

slide it out of the computer.

Figure 42. Removing the flex storage enclosure

P330 User Guide

Summary of Contents for ThinkStation P330







































































































































Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands

Lenovo ThinkStation P330, User Manual

Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands