Lenovo ThinkStation P330 User Manual Download Page 76

Page: 76 / 134

• To complete the installation or replacement, go to “Completing the parts replacement” on page 89.

2.5-inch storage drive

To replace the 2.5-inch storage drive, do the following:

1. Prepare your computer. See “Preparing your computer” on page 24.

2. Locate the storage-drive bay.

3. To remove the 2.5-inch storage drive, do the following:

a. Disconnect the signal cable and the power cable from the storage drive.

b. Push the tab of the storage-drive bracket as shown and pull the tab outward to remove the storage

drive from the storage-drive bay.

Figure 81. Removing the 2.5-inch storage drive with 3.5-inch storage-drive bracket

P330 User Guide

Summary of Contents for ThinkStation P330







































































































































Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands

Lenovo ThinkStation P330, User Manual

Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands