Lenovo ThinkStation P330 User Manual Download Page 82

Page: 82 / 134

c. Pull the handle of the plastic 3.5-inch storage-drive bracket to remove the storage drive from the

type-1 storage-drive cage.

Figure 88. Removing the 3.5-inch storage drive

d. Flex the sides of the bracket to remove the storage drive from the bracket.

4. To install a 3.5-inch storage drive in the type-1 storage-drive cage, do the following:

a. To install a new storage drive into the bracket, flex the bracket and align pin

, pin

, and pin

on the bracket with the corresponding holes in the storage drive. Do not touch the circuit board

on the storage drive.

Figure 89. Installing the storage drive into the bracket

P330 User Guide

Summary of Contents for ThinkStation P330







































































































































Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands

Lenovo ThinkStation P330, User Manual

Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands