Lenovo ThinkStation P330 User Manual Download Page 13

Page: 13 / 134

You can install a 3.5-inch storage drive or a 2.5-inch storage drive in this cage.

SD card slot (available on some models)

An SD card is installed in some computer models.

Flex bay (available on some models)

Depending on your computer model, one of the following devices might be installed in the flex bay:

• Flex module

• Front-access storage enclosure

• Flex storage enclosure

M.2 solid-state drive slot

One M.2 solid-state drive is installed in some computer models.

Type-2 storage-drive cage

You can install a 2.5-inch storage drive in this cage.

Type-1 storage-drive bay

You can install a 3.5-inch storage drive or a 2.5-inch storage drive in the storage-drive bay.

PCIe card slots (3)

You can install compatible PCIe cards and PCIe solid-state drives in the PCIe card slots.

Chapter 1

Meet your computer

Summary of Contents for ThinkStation P330







































































































































Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands

Lenovo ThinkStation P330, User Manual

Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands