Lenovo ThinkStation P330 User Manual Download Page 57

Page: 57 / 134

a. Flex both sides of the bracket and align pins

on the bracket with the corresponding holes in the

new 3.5-inch storage drive.

Notes:

• Ensure that the circuit board faces downward and the connectors face toward the rear of the

bracket.

• Do not touch the circuit board on the storage drive.

Figure 49. Installing the 3.5-inch storage drive into the bracket

b. Slide the bracket with the new 3.5-inch storage drive into the front-access storage enclosure until it

snaps into position.

Figure 50. Installing the 3.5-inch storage drive into the front-access storage enclosure

c. Press the notch to secure the enclosure cover and lock the enclosure cover with the key.

What to do next:

Chapter 6

Hardware removal and installation

Summary of Contents for ThinkStation P330







































































































































Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands

Lenovo ThinkStation P330, User Manual

Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands