Lenovo ThinkStation P330 User Manual Download Page 69

Page: 69 / 134

e. Install the storage converter with the bracket into the enclosure from the rear until the drive snaps

into position.

Figure 71. Installing the storage converter with the bracket into the enclosure

7. Pivot the rear cover of the enclosure inward until you hear a click. The rear cover is secured in place.

Figure 72. Pivoting the rear cover inward

8. Connect the signal cable and the power cable to the storage drive.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 89.

Chapter 6

Hardware removal and installation

Summary of Contents for ThinkStation P330







































































































































Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands

Lenovo ThinkStation P330, User Manual

Search results

Summary of Contents for ThinkStation P330

Reviews:

Related manuals for ThinkStation P330

Brands by name

Popular brands