manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 79

4

. LUBRICATION SYSTEM

     

4-5

     MXU 300/250

Measure the inner rotor-to-outer rotor
clearance.

Service Limit: 0.2 mm (0.008 in)

Measure the pump body-to-outer rotor
clearance.

Service Limit: 0.25 mm (0.01 in)

ASSEMBLY

Install the outer rotor, inner rotor and pump
shaft into the pump body.

Install the dowel pin.
Install the pump cover by aligning the hole
in the cover with the dowel pin.
Tighten the screw to the specified torque.

Torque : 0.2 kgf-m (2 Nm, 1.5 lbf-ft)

INSTALLATION

Reverse the “OIL PUMP REMOVAL”
procedures.

Outer Rotor

Pump Body

Inner Rotor

Outer Rotor

Outer Rotor

Inner Rotor

Dowel Pin

Pump Cover

Oil Pump Bolts

Insert the pump shaft by aligning the flat
on the shaft with the flat in the inner
rotor.

＊

Install the oil pump with the arrow on
the pump body facing up and fill the oil
pump with engine oil before installation.

＊

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands