manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 149

9.

DRIVE AND DRIVEN PULLEYS

9-8

     MXU 300/250

DRIVE BELT INSPECTION

Check the drive belt for cracks, separation or

abnormal or excessive wear.

Measure the drive belt width.

Service Limit (replace if below):

22 mm (0.88 in)

CLUTCH OUTER INSPECTION

Inspect the clutch outer for wear or damage.

Measure the clutch outer I.D.

Service Limit (replace if over):

153.5 mm (6.14 in)

CLUTCH/DRIVEN PULLEY
DISASSEMBLY

Hold the clutch/driven pulley assembly with

the clutch spring compressor.

Special tool:
Clutch Spring Compressor   E027

Set the clutch spring compressor in a vise and

remove the clutch drive plate nut.

Clutch Spring Compressor

Lock Nut Wrench

Be sure to use a clutch spring

compressor to avoid spring damage.

＊

Use specified genuine parts for

replacement.

＊

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands