manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 323

16

. BATTERY/CHARGING SYSTEM/

A.C. GENERATOR

16-9

     MXU 300/250

A.C. GENERATOR INSPECTION

Disconnect the A.C. generator connector.

Check the continuity between the yellow

wires and ground.

There should be continuity between the

yellow wires and no continuity between

each yellow wire and ground.

Resistance 

(at 20°C):

Yellow

～

Yellow

1.6

～

2.5

Ω

A.C. GENERATOR/FLYWHEEL

REMOVAL

Remove the right crankcase cover. (Refer to

the “WATER PUMP SHAFT REMOVAL”

section in the chapter 12)

Remove the pulser coil screws and then

remove the A.C. generator wire set plate.
Remove the A.C. generator bolts and then

remove A.C. generator and pulser coil from

right crankcase cover.

Remove the oil through guide and spring.

Bolts

Screws

Set Plate

Pulser Coil

A.C. Generator

Spring

Oil Through Guide

This test can be made without removing

the stator from the engine.

＊

When removing the pulser coil and

stator, be careful not to damage them to

avoid shorted or broken wire.

＊

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands