manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 221

12

. COOLING SYSTEM

     

12-15

    MXU 300/250

THERMOSTAT INSPECTION

Suspend the thermostat in a pan of water

over a burner and gradually raise the water

temperature to check its operation.

Technical Data

  Begins to open

80

±

2

℃

  Full-open

90

℃

  Valve lift

3.5

～

4.5 mm

THERMOSTAT INSTALLATION

The installation sequence is the reverse of

removal.

Fill the cooling system with the specified

coolant. (page 12-7)

O-ring

Thermosensor

Thermostat

Thermometer

•

Do not let the thermostat touch the pan

as it will give a false reading.

•

Replace the thermostat if the valve

stays open at room temperature.

•

Test the thermostat after it is opened for

about 5 minutes and holds the

temperature at 70

℃

.

＊

Replace the O-ring with a new one and

apply grease to it.

＊

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands