manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 307

15.

 

REAR WHEEL/AXLE/SUSPENSION/
DRIVING MECHANISM

15-38

     MXU 300/250

Make sure that the gear assembly rotates
smoothly without binding.

SWINGARM (MXU 300)

SWINGARM INSPECTION/BEARING
REPLACEMENT

Inspect the dust seal for wear or damage.
If any damages are found, replace them with
new ones.

Remove the dust seals.
Remove the swingarm bearing.

Inspect the swingarm bearing, outer race
and bearing plate, if any damages are found,
replace the swingarm bearing with a new
one.

Dust Seal                                            Bearing

Bearing                                          Outer Race

                                                    Bearing Plate

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands