manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 71

3

. INSPECTION/ADJUSTMENT

 

3-24

   MXU 300/250

CABLE INSPECTION AND
LUBRICATION

Inspect the cable sheath.
Replace if damage.
Check the cable operation.
Lubricate or replace if unsmooth operation.

LEVER LUBRICATION

Lubricate the pivoting parts of each lever.

REAR SUSPENSION
LUBRICATION (MXU 250)

Inject grease into the nipples using a grease
gun until slight over flow is observed from
the thrust covers.

Nipple

Damaged cable sheath may cause
corrosion and interfere with the cable
movement. An unsafe condition may
result so replace such cable as soon as
possible.

＊

Hold cable end high and apply several
drops of lubricant to cable.

＊

Wipe off the excess grease.

＊

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands