manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 68

3

. INSPECTION/ADJUSTMENT

     

3-21

   MXU 300/250

DRIVE CHAIN SLACK
ADJUSTMENT (MXU 250)

Before checking and/or adjusting, rotate the
rear wheels several revolutions and check
slack at several points to find the tightest
point. Check and/or adjust the chain slack
with the rear wheels in this “tightest”
position.

Place the machine on a level place.

Check drive chain slack.
Adjust if out of specification.

Drive chain slack (A):

30 ~ 40 mm (1.2 ~ 1.6 in)

Adjust drive chain slack:
Loosen the caliper holder bolt and two axle
hub holding bolt.

Provide a proper pin and pass the pin
through the axle hub and driven sprocket.

Bolt

Too little of chain slack will overload the
engine and other vital parts; keep the
slack within the specified limits.

＊

Wheels should be on the ground without
the rider on it.

＊

Bolts

Driven Sprocket

Pin

Axle Hub

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands