manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 347

19

. LIGHTS/SWITCHES

19-2

     MXU 300/250

BULBS REMOVAL

HEADLIGHT

Remove the front fender. (See page 2-8)

Remove the rubber boot from the headlight

case.
Disconnect the headlight wire connector.

Relax the lock clips to remove the bulb and

replace with a new one.

Install the bulb, aligning the bulb socket

groove with the bulb tab and set the lock

clips.
Connect headlight wire connector.
Install the rubber boot.
Install the front fender in the reverse order

of removal.

POSITION LIGHT

Remove the bulb socket by pulling it out.

Remove the bulb.
Install the bulb in the reverse order of

removal

Rubber Boot

Bulb Socket

Lock Clips

Lock Clip

Headlight Connector

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands