manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 330

17

. IGNITION SYSTEM

     

17-5

     MXU 300/250

Test the ignition unit using the ignition unit

tester.

Connect the special connector to the

ignition unit coupler and ignition unit tester.

Switch Range Good CDI

Faulty CDI

1. OFF
2. P
3. EXT
4. ON1
5. ON2

No spark
No spark
No spark

Good spark
Good spark

⎯⎯
⎯⎯

Good spark

No spark
No spark

If the ignition unit is faulty, replace it with a

new one.

CHANGE REAR CONTROL
INSPECTION
Testing Range

(at 20°C)

Note: The readings in this table are taken
     with a YF-3501 Tester.

                                                 
                                                       

              Probe

⊕

(-)Probe

Green

Yellow/

Brown

Light Green/

Red

Green/

Pink

Green/

Yellow

Black/

White

Black

Green

14

∞

∞

7.85M

7.85M

10K

Yellow/

Brown

18

∞

∞

7.85M

7.85M

10K

Light Green/

Red

7.85M

7.85M

11

∞

∞

7.85M

Green/

Pink

7.85M

7.85M

9

∞

∞

7.85M

Green/

Yellow

∞

∞

∞

∞

∞

Black/

White

∞

∞

∞

∞

11

∞

Black

10K

10K

∞

∞

7.85M

7.85M

Spark

Window

Ignition Coil

CDI Unit

Spark Plug

CDI Tester

Operate the ignition unit tester by

following the manufacturer‘s

instructions.

＊

Change Gear Control

Unit: 

Ω

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands