manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 231

13

. BRAKE SYSTEM

     

13-9

   MXU 300/250

FRONT BRAKE CALIPER

REMOVAL

Remove the front wheel. (page 14-3)
First drain the brake fluid from the
hydraulic brake system. (page 13-4)
Remove the brake pad pins.

Remove the brake fluid tube bolt.
Remove the two bolts attaching the brake
caliper.
Remove the brake caliper.

DISASSEMBLY

Remove the brake pads. (page 13-3)

Remove the brake pad spring plate.

Remove the piston from the brake caliper.
If necessary, use compressed air to squeeze
out the piston through the brake fluid inlet
opening and place a shop towel under the
caliper to avoid contamination caused by
the removed piston.
Check the piston cylinder for scratches or
wear and replace if necessary.

Spring Plate

Brake Pad Pins

Bolts

Fluid Tube Bolt

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands