manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 106

6

. ENGINE REMOVAL

 

6-8

    MXU 300/ 250

ENGINE REMOVAL (MXU 300)

Drain engine oil and transmission oil.
(Refer to chapter 3).
Remove frame covers and exhaust pipe.
(Refer chapter 2).
Remove the air cleaner housing and
carburetor. (Refer to chapter 5).

Disconnect the spark plug from the cylinder
head.
Disconnect the spark coil connectors from
the spark coil, then remove the two bolts
and spark coil.

Disconnect the speedometer cable.

Disconnect the crankcase breather from the
cylinder head cover.
Disconnect the vacuum hose from the inlet
pipe.

                        Bolts                    Connectors

          Spark Plug                                Spark Coil

                Speedometer Cable

              Speedometer Cable

                                                      Vacuum Hose

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands