manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 59

3

. INSPECTION/ADJUSTMENT

 

3-12

   MXU 300/250

Clean the oil strainer with solvent.
Inspect the O-ring and replace if damaged.
Reinstall the O-ring, oil strainer,
compression spring and oil filter cap.
Tighten the oil filter cap to specification.

Torque: 1.5 kgf-m (15 Nm, 11 lbf-ft)

Fill the engine with oil and install the oil fill
cap.

Oil Capacity

:

  At disassembly:
        1.6 liter (1.4 lmp qt, 1.7 Us qt)
  At change:
        1.4 liter (1.23 lmp qt, 1.48 Us qt)

TRANSMISSION OIL

REPLACEMENT

Place the machine on a level place.
Place a container under the engine.
Remove the oil filler bolt (1).

O-ring

Compression Spring

Oil Strainer

Oil Filter Cap

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands