KYMCO MXU 300 - User Manual Download Page 234

Page: 234 / 352

. BRAKE SYSTEM

13-12

MXU 300/250

REAR HYDRAULIC BRAKE

REAR BRAKE PADS (MXU 250)
Removal

Remove the brake pads cover.
Remove the cotter pin and then pull out the
brake pad pin from the caliper.

Remove the brake spring plate and then
remove brake pads.

Installation

Reverse the “REAR BRAKE PADS
REMOVAL” procedures.

REAR BRAKE PADS (MXU 300)
Replacement

Remove the left rear wheel (page 15-4).

The rear and front brake pads are replaced
the same (page 13-3).

Brake Pad Cover

Cotter Pin

Brake Pad Pin

Spring Plate

Brake Pads

Spring Plate Small End

Brake Pad Pin

Spring Plate Big End

•

Make sure put the spring plate big end
on the rear caliper.

•

Make sure put the spring plate small
end on the rear pads.

•

Make sure brake pad pin over the
spring plate.

＊

Bolts Bolts

Brake Pad Pins Brake Pad Pins

Summary of Contents for MXU 300 -

































































































































































































































































































































































Search results

Summary of Contents for MXU 300 -

Reviews:

Brands by name

Popular brands

KYMCO MXU 300 -, User Manual

Search results

Summary of Contents for MXU 300 -

Reviews:

Brands by name

Popular brands