manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 50

3

. INSPECTION/ADJUSTMENT

     

3-3

   MXU 300/250

MAINTENANCE SCHEDULE

This chapter includes all information necessary to perform recommended inspections and
adjustments. These preventive maintenance procedures, if followed, will ensure more reliable
vehicle operation and a longer service life. The need for costly overhaul work will be greatly
reduced. This information applies to vehicles already in service ad well as new vehicles that are
being prepared for sale. All service technicians should be familiar with this entire chapter.

•

In the interest of safety, we recommend these items should be serviced only by an authorized

KYMCO motorcycle dealer.

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands