manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 241

13

. BRAKE SYSTEM

     

13-19

   MXU 300/250

REAR BRAKE CALIPER

REMOVAL (MXU 250)

Drain brake fluid of both the rear brake side
and the combination brake side. (page 13-
13)

Remove the brake pads. (page 13-12)

Remove the caliper mounting bolts and
remover the caliper.

Remove the caliper housing bolts.

Using an air blow gun, pressurize the
caliper fluid chamber to push out the piston.

To prevent brake fluid from splashing on

the parts nearby, cover the parts with
cloth.

＊

Slightly loosen the caliper housing bolts

before removing the caliper mounting
bolts to facilitate later disassembly.

＊

Bolts

Bolts

Place a rag over the piston to prevent it
from popping out and flying and keep
hand off the piston.
Be careful of brake fluid which can
possibly splash.
Do not use high pressure air but
increase the pressure gradually.

＊

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands