KYMCO MXU 300 - User Manual Download Page 260

Page: 260 / 352

14.

FRONT WHEEL/FRONT SUSPENSION/

STEERING SYSTEM

14-15

MXU 300/250

TIE-ROD

REMOVAL/INSPECTION

Remove the cotter pin and nut attaching the

tie-rod and steering column.
Remove the cotter pin, washer and nut

attaching the tie-rod and steering knuckle.
Then remove tie-rods, using the special tool

(page 14-8).

Special tool:
Tie-rod ball join remover

F011

Inspect the tie-rod.

Bend/damage

→

Replace.

Check the tie-rod end movement.
Tie-rod end exists free play or turns
roughly

→

Replace.

Check the tapered surface of the tie-rod end.
Pitting/wear/damage

→

Replace.

Nut

Cotter Pin

Nut

Cotter Pin

Summary of Contents for MXU 300 -

































































































































































































































































































































































Search results

Summary of Contents for MXU 300 -

Reviews:

Brands by name

Popular brands

KYMCO MXU 300 -, User Manual

Search results

Summary of Contents for MXU 300 -

Reviews:

Brands by name

Popular brands