manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 232

13

. BRAKE SYSTEM

 

13-10

   MXU 300/250

Push the piston dust seal inward to remove.

Pushing the piston oil seal outward to
remove it.

Clean the seals groove with brake fluid.

INSPECTION

Inspect the caliper cylinder wall and piston
surface for scratch, corrosion or other
damages.
If any abnormal condition is noted, replace
the caliper.

ASSEMBLY

Clean all removed parts.
Apply silicon grease to the piston and oil
seals. Lubricate the brake caliper cylinder
inside wall with brake fluid.
Install the oil seal and dust seal.
Install the brake caliper piston with grooved
side facing out.

Wipe off excessive brake fluid with a clean
shop towel.

Inner Oil Seal

Dust Seal

Be careful not to damage the piston
surface.

＊

Install the piston with its outer end
protruding 3

～

5 mm beyond the brake

caliper.

＊

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands