manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 127

7

. CYLINDER HEAD/VALVES

 

7-10

     MXU 300/250

CYLINDER HEAD

REMOVE

Remove the camshaft (page 7-4).
Remove the carburetor. (Refer to the
“carburetor remove” section in the chapter
5)
Remove the exhaust muffler (page 2-11).

Remove the two bolts and then remove the
carburetor intake manifold.

Remove the bolt and disconnect the
thermostat.

Remove the two cylinder head bolts.
Remove the cylinder head.

CYLINDER HEAD DISASSEMBLY

Remove the valve spring cotters, retainers,
springs, spring seats, oil seals and valves
using a valve spring compressor.

Special tool:
Valve Spring Compressor   E040

Bolts

Intake Manifold

Bolt

Bolt

Bolts

Valve Cotter

Retainer

Springs Springs Seat

Oil Seal

Valve

Spring Compressor

•

Be sure to compress the valve springs
with a valve spring compressor.

•

Mark all disassembled parts to ensure
correct reassembly.

＊

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands