manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 263

14.

 FRONT WHEEL/FRONT SUSPENSION/

   STEERING SYSTEM

 

14-18

   MXU 300/250

HANDLEBAR

REMOVAL/INSPECTION

Remove the following parts:
Seat, front cover, fuel tank cover, front

fender and handlebar cover.
Refer to the “FENDERS” section in the

CHAPTER 2

Remove the right and left master cylinder

and remove bands then disconnect the rear

and front fluid tube from the handlebar.

Remove the two screws and remove the

handlebar switch.
Remove the two screws and remove throttle

unit.

Remove the four handlebar holder bolts,

then remove handlebar cover and handlebar

holder.

Bolts

Brake Fluid Tube

Screws

Screws

Bolts

Handlebar Holder

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands