manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 324

16

. BATTERY/CHARGING SYSTEM/

A.C. GENERATOR

16-10

     MXU 300/250

Hold the flywheel with a flywheel holder

and remove flywheel nut and wash.

Special tool:
Flywheel holder   E021

Remove the flywheel with a flywheel puller.

Special tool:
Flywheel puller   E003

INSTALLATION

Reverse the “REMOVAL” procedures.
Install the flywheel, washer and tighten the

nut.

Torque: 6 kgf-m (60 Nm, 43 lbf-ft)

Install the oil through guide and spring.
Install the A.C. generator onto the right

crankcase cover and tighten the bolts.

Torque: 0.9 kgf-m (9 Nm, 6.5 lbf-ft)

Install the right crankcase cover.

Nut

Flywheel

Flywheel Holder

Flywheel Puller

Key

Groove

Washer

‧

Before installation, check and make

sure that the inside of the flywheel is

not contaminated.

‧

Make sure install the flywheel onto

the crankshaft by aligning the key on

the crankshaft with the groove in the

flywheel.

＊

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands