manualshive.com logo in svg

KYMCO MXU 300 -, User Manual

Share
Download
KYMCO MXU 300 - User Manual Download Page 332

17

. IGNITION SYSTEM

     

17-7

     MXU 300/250

Measure the spark plug cap resistance.
Remove the spark plug cap and measure the

spark plug resistance.

Resistance

: 4.2

～

5.2K

Ω

/20

◦

C

PERFORMANCE TEST

Test the performance with a ignition unit

tester.

If the spark is weak, inspect the spark plug

and ignition unit. If both of them are normal,

replace the ignition coil with a new one.

PULSER COIL

INSPECTION

Remove the front fender. (Refer to the

chapter 2)
Disconnect the pulser coil wire coupler and

measure the resistance between the blue/

yellow and green/white wire terminals.

Resistance

: 105

～

110

Ω

/20

◦

C

Refer to the “A.C.

GENERATOR/FLYWHEEL” section in the

chapter 16 to remove or install.

Ignition Coil

CDI Unit

Spark Plug

CDI Tester

•

Operate the ignition unit tester by

following the manufacturer‘s

instructions.

•

Use the special connector to connect

the ignition unit.

＊

Measure the resistance in the XK

Ω

 range

of the electric tester.

＊

Summary of Contents for MXU 300 -

































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands