KYMCO MXU 300 - User Manual Download Page 219

Page: 219 / 352

. COOLING SYSTEM

12-13

MXU 300/250

THERMOSENSOR

THERMOSENSOR REMOVAL

Drain the coolant. (page 12-7)
Disconnect the thermosensor wire.

Remove the thermosensor from the

thermostat.

THERMOSENSOR INSPECTION

Suspend the thermosensor in a pan of water

over a burner and measure the resistance

through the sensor as the water heats up.
Temperature(

℃

) 50

100 120

Resistance(

Ω

)

154

THERMOSENSOR INSTALLATION

Apply 3-BOND No. 1212 sealant or

equivalent to the thermosensor threads and

install it into the thermostat housing.

Connect the thermosensor wire.

Fill the radiator with coolant. (page 12-7)

Thermosensor Connectsor

Thermosensor

Be sure to bleed air from the cooling

system.

＊

Thermosensor

Summary of Contents for MXU 300 -

































































































































































































































































































































































Search results

Summary of Contents for MXU 300 -

Reviews:

Brands by name

Popular brands

KYMCO MXU 300 -, User Manual

Search results

Summary of Contents for MXU 300 -

Reviews:

Brands by name

Popular brands