KYMCO MXU 300 - User Manual Download Page 352

Page: 352 / 352

. LIGHTS/SWITCHES

19-7

MXU 300/250

NEUTRAL/REVERSE

SWITCHES

INSPECTION

Disconnect the neutral/reverse switch wire

connector. (See page 6-4 or 6-10)

Check for continuity between the switch

side connector terminal and engine ground.

NEUTRAL SWITCH
There should be continuity with the

transmission in neutral and no continuity

with it in any gear except neutral.

REVERSE SWITCH
There should be continuity with the

transmission in reverse and no continuity

with it in any gear except reverse.

REPLACEMENT
Remove drive and driven pulley. (Refer to

chapter 9)

Remove the two bolts and set plates.
Remove neutral/reverse switch.

Install a new switch with a new O-ring

(apply engine oil to O-ring).

Set Plates

Bolts

Make sure that the lever on the

neutral/reverse switch correctly engages

with the locating slot on the shift shaft.

＊

Neutral/Reverse Switch

O-ring

Lever

Summary of Contents for MXU 300 -

































































































































































































































































































































































Search results

Summary of Contents for MXU 300 -

Reviews:

Brands by name

Popular brands

KYMCO MXU 300 -, User Manual

Search results

Summary of Contents for MXU 300 -

Reviews:

Brands by name

Popular brands