Korg M3, Parameter Manual

Page: 230 / 647

Sequencer mode
220
Note that, in Sequencer mode, only the Song’s X–Y CCs can
be sent to external MIDI instruments; the individual
Program’s X–Y CCs are only used internally.
Enable CC Control [Off, On]
When this box is checked, the X–Y position will control the
CCs assigned to +X, –X, +Y, and –Y, as set below.
When this box is not checked, the CC assigned to +X, –X,
+Y, and –Y will have no effect, but the MIDI CC numbers
specified by X (X–Y Mode) and Y (X–Y Mode) in Global P2:
Controllers– MIDI CC# Assign can be transmitted and
received.
For more information, please see “X–Y control and MIDI,”
above.
This parameter affects only the Song X–Y CCs. Even if this is
turned Off, the individual Programs’ X–Y CCs will still
function normally.
X Mode [Positive, Negative, Xfade, Split]
You can set up the X–Y CCs to send out CCs in several
different patterns, as shown in the graphic below. This
controls the pattern for the X axis. Also, it applies only to the
Song’s X–Y CCs, and has no effect on the individual
Program X–Y CCs.
Positive sends out only +X, starting at 0 at the far left, and
increasing to 127 at the far right. –X is disabled in this mode.
Negative sends out only –X, starting at 0 at the far right, and
increasing to 127 at the far left. In this mode, +X is grayed
out.
Xfade sends out both +X and –X, overlapping throughout
the X axis. As one increases, the other decreases.
Split sends out both +X and –X, with a split in the center. +X
is sent when the point moves to the right of the center, and
–X is sent when the point moves to the left of center.
+X [Off…MIDI CC#119]
This assigns the controller transmitted by the +X direction.
You can use this as an AMS source to control Program
parameters, or as a Dmod source to control Effects
parameters. It will be grayed out if the X Mode, above, is set
to Negative.
–X [Off…MIDI CC#119]
This assigns the controller transmitted by the –X direction. It
will be grayed out if the X Mode, above, is set to Positive.
The selections are the same as for +X, above.
X–Y CC Modes
Y Mode [Position, Negative, Xfade, Split]
This controls the X–Y CC pattern for the Y axis. For more
information, please see the description under X Mode,
above.
+Y [Off…MIDI CC#119]
This assigns the controller transmitted by the +Y direction. It
will be grayed out if the Y Mode, above, is set to Negative.
The selections are the same as for +X, above.
–Y [Off…MIDI CC#119]
This assigns the controller transmitted by the –Y direction. It
will be grayed out if the Y Mode, above, is set to Positive.
The selections are the same as for +X, above.
X–Y Graphic:
X–Y Graphic
The X–Y graph shows a representation of the volume
change when using Equal Power mode or the Center
Volume setting.
Track Select [01…16]
This selects the track whose data will be shown in the X–Y
graph.
1–4(5)b: Track Info
Selected Track Info:
Track Number:
Track Category:
For more information, please see “1–2(3)c: Track Info” on
page 218.
+127 –127 0
+X CC 0 127
+127 –127 0
–X CC 127 0
+127 –127 0
+X CC 0 127
–X CC 127 0
+127 –127 0
+X CC
0 127
–X CC
127 0
X-Axis
Positive
X-Axis
Negative
X-Axis
Xfade
X-Axis
Split
Generates only +X,
increasing from left to right.
Generates both +X and –X.
One increases as the other
decreases. Generates both +X and –X.
Both are 0 in the center.
+X increases to the right;
–X increases to the left.
Generates only –X,
increasing from right to left.