Program: Menu Command Auto Sampling Setup
109
3. Press the SAMPLING START/STOP switch or Play but-
ton.
The selected WAVE file will be played.
4. Press the SAMPLING START/STOP switch or Stop
button once again to stop playback.
If the WAVE file is mono, the same sound will be output to
L/R.
Auto Sampling Setup
Auto Sampling Setup
is available on the Sampling/Audio
In tab of the Play page.
This command automatically configures the Program mode
sampling-related parameters, making it easy for you to
sample an external audio source or to resample your
performance as you play a Program. You can also use this
command to initialize the sampling settings.
After using Auto Sampling Setup, you can further adjust
any of the settings to suit your needs as described in the
paragraphs of each section.
When you execute this command, the applicable
parameters will be set automatically. You cannot use the
COMPARE
switch to recall the previous settings.
1. Select “Auto Sampling Setup” to open the dialog box.
2. Press a radio button to select the type of settings you
want to make.
Initialize:
Initializes the sampling-related parameters to
their default state.
Resample Program Play:
Sets the sampling-related
parameters to allow you to play a Program and resample
your performance.
REC Audio Input:
Sets the sampling-related parameters so
that you can sample an external audio source. With these
settings, you can play a Program while sampling, but only
the external input will be recorded.
3. The settings for the rest of the procedure will depend
on what you selected in step 2. (For details, please see
the explanations below.)
If you selected Initialize:
1. Refer to Auto Sampling Setup steps 1 and 2, and select
Initialize.
2. Press the OK button to execute the command. If you
decide not to execute, press the Cancel button.
For the parameters and values that will be set, please see
page 110.
Resample Program Play,
If you selected Resample Combination Play:
1. Refer to Auto Sampling Setup steps 1 and 2, and select
Resample Program Play.
2. Use Save to select either RAM or MEDIA as the desti-
nation to which the resampled data will be written.
If you choose RAM, the sampled data will be written into
RAM. If this is set to MEDIA, the sampled data will be used
to create a WAVE file, which will then be saved on an
external USB storage device (such as a hard disk). For more
information, please see “Save to” on page 12.
3. If you selected RAM for Save to, you can also specify
whether the sample will be automatically converted to
a program after resampling.
If you want to convert the sample, check the Convert to
Program
option, and use Program to specify the desired
convert-destination program.
4. Press the OK button to execute Resample Program Play.
If you decide not to execute, press the Cancel button.
(See “Automatically-set parameters and their values”
on page 110)
Execute the command, and then resample
1. Press the SAMPLING REC switch and then the SAM-
PLING START/STOP switch, and then play a note on
the keyboard etc.
Since Trigger (Prog 0–7b) is set to Note On, sampling will
begin at the first note-on.
2. When you’ve finished performing, press the SAM-
PLING START/STOP switch to stop resampling.
Note: If Save to was set to RAM and Convert to Program
was checked when you executed Resample Program (/
Combination) Play, and you continue sampling without
changing the settings, the samples will automatically be
assigned to C#2, D2 ... etc. When you execute Resample
Program (/Combination) Play
once again and sample, a
new multisample will be created.
Auditioning the sampled data
• If Save to was set to RAM and Convert to Program was
checked when you executed, you can select the program
you specified as the conversion-destination, and play the
C2 note to hear the result.
If Convert to Program was not checked, select the
sample in Sampling mode and audition it.
• If Save to was set to MEDIA when you executed, use the
menu command Select Directory to audition the result.
Note: If you want to change the sample number to be
sampled (when Save to is RAM), use the menu command
Select Bank & Sample No.
to change it.
Changing the writing destination
If you want to change the destination to which the WAVE
file will be saved (when Save to is MEDIA), use the menu
command Select Directory to make the change.
Changing the way in which sampling begins
If you want to change the way in which sampling begins,
change the Trigger setting (Prog 0–8c).
Summary of Contents for M3
