Kenwood TK-2170 SERIES Function Reference Download | Manualshive

Page: 96 / 142

background image

20 FLEETSYNC

84

Confidential

FUNC (K)/Ver. 1.01

20.2.2 Making a Selcall

The transceiver waits to receive a call under the following
conditions when the transceiver receives a Selcall.
The conditions for the FleetSync ID to match when
receiving a Selcall are as follows.

Table 20-4 Call Type Conditions for Unmuting

Note:

“FleetSync” must be selected from the

Channel Edit

window >

Optional Signaling

dropdown list.

Individual Call/ Group Call

A user can respond to the party appearing on the
display by pressing the

PTT

switch or

Side 2

key.

The transceiver only controls the mute function and
does not enter Call Mode in the following conditions:
•

If the transceiver receives a call from the party
having Fleet inhibited by the Interfleet
configuration.

•

When the transmitting party’s ID is outside of the
Unit ID Encode Block range.

•

When the ID has “Yes” configured for Transmit
Inhibit in the Selcall List.

The display returns to the previous display when a key
is pressed. The display also returns to the previous
display after the Auto Reset Timer expires if LCD
(Auto Reset) is enabled.

z

Display when an ID is registered in the ID List
(Individual Call)

z

Display when no ID is registered in the ID List
(Individual Call)

z

Display when an ID is registered in the ID List
(Group Call)

z

Display when no ID is registered in the ID List
(Group Call)

Fleet Call

A user can make a call to the party appearing on the
display by pressing the

PTT

switch or

Side 2

key.

The transceiver only controls the mute function and
does not enter Call Mode when receiving a call from a
party having a Fleet that is not registered in the ID
List.
The display returns to the previous display when a key
is pressed. The display also returns to the previous
display after the Auto Reset Timer expires if LCD
(Auto Reset) is enabled.

z

Display when an ID is registered in the ID List

z

Display when an ID is not registered in the ID
List

Supervisor Call/ Broadcast Call

A user can make a call to the party appearing on the
display by pressing the

PTT

switch or

Side 2

key if an

ID is registered in the ID List.
The transceiver only controls the mute function and
does not enter Call Mode when receiving a call from
the party having an ID that is not registered in the ID
List.
The display returns to the previous display when a key
is pressed. The display also returns to the previous
display after the Auto Reset Timer expires if LCD
(Auto Reset) is enabled.

Call Type

Conditions to Unmute

Fleet

fff: 100 to 399

ID

iiii: 1000 to 4999

Individual Call

Match

Match

Group Call

Match

Group ID matches

Fleet Call

Match

ALL ID

Supervisor Call

ALL Fleet

Match

Broadcast Call

ALL Fleet

ALL ID

«
...
94
95
96
97
98
...
»

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments

Related manuals for TK-2170 SERIES

Brand: Tabor Electronics Pages: 39

Brand: unicraft Pages: 60

Voyager MAX KA900

Brand: Kaito Pages: 29

Brand: Tesco Pages: 2

Brand: F&U Pages: 4

Sure Cross MultiHop H3E-NB-KR

Brand: Banner Pages: 8

Brand: Mimomax Pages: 56

Brand: K&S BASIC Pages: 23

Brand: ZIPPER MASCHINEN Pages: 93

Brand: Audiovox Pages: 28

Brand: Richter Pages: 12

Brand: kchibo Pages: 4

Brand: MULTIQUIP Pages: 72

Brand: NuTone Pages: 28

Brand: BC Pages: 19

Brevini CMI Series

Brand: DANA Pages: 8

TOYOTA CQ-MS7920A

Brand: Panasonic Pages: 24

Brand: Xact Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands