manualshive.com logo in svg

Kenwood TK-2170 SERIES, Function Reference, Page: 6 / 142

Share
Download
Kenwood TK-2170 SERIES Function Reference Download Page 6

CONTENTS

IV

Index

Confidential

FUNC (K)/Ver. 1.01

20.5 Long Message Function ................................94

20.5.1

Sending a Long Message .............................94

20.5.2

Receiving a Long Message ..........................94

20.5.3

Long Message on Data Zone-CH/GID..........95

20.6 Stack..............................................................95

20.6.1

Stores the Latest Received Messages .........97

20.6.2

Caller ID Stack..............................................98

20.6.3

Message Memory .........................................98

20.7 Configuring FleetSync ...................................98

20.7.1

Fleet/ ID (Own) .............................................99

20.7.2

Unit ID Encode Block....................................99

20.7.3

FleetSync Baud Rate....................................99

20.7.4

Message Display Type .................................99

20.7.5

PC Interface Protocol..................................100

20.7.6

Manual Dialing ............................................100

20.7.7

Selective Call Alert LED..............................100

20.7.8

Interfleet Call...............................................100

20.7.9

Group ID .....................................................100

20.7.10 Auto Reset Timer........................................101
20.7.11 Alert Tone (Individual Call) .........................101
20.7.12 Alert Tone (Other Selective Calls) ..............101
20.7.13 Alert Tone (Paging Call) .............................101
20.7.14 Alert Tone (Status Message Call/ 

Short Message Call) ...................................101

20.7.15 Alert Tone (Emergency Response) ............102
20.7.16 Unit ID Serial Output...................................102
20.7.17 GTC Count..................................................102
20.7.18 Number of Retries.......................................102
20.7.19 Transmit Busy Wait Time............................103
20.7.20 Maximum ACK Wait Time...........................103
20.7.21 ACK Delay Time .........................................103
20.7.22 Transmit Delay Time 

(Receive Capture).......................................103

20.7.23 Data Transmit Modulation Delay Time .......103
20.7.24 Random Access (Contention).....................104
20.7.25 Data Transmit with QT/DQT .......................104

21 SCAN ....................................................105

21.1 Scan Operation............................................105

21.1.1

Conditions to Start Scanning ......................105

21.1.2

Conditions to Resume Scanning ................105

21.1.3

Operations when Scan Cannot Resume ....106

21.1.4

Operation after Manually Changing the 
Zone-CH/GID during the Scan....................106

21.1.5

Operations when Manually Changing the 
Zone-CH/GID while Scan Pauses to 
Receive a Call.............................................106

21.1.6

Transceiver Operation during the Scan ......106

21.1.7

Single Scan.................................................108

21.2 Multi Scan....................................................108
21.3 List Scan (TK-3173 only) .............................109
21.4 Priority Scan ................................................109
21.5 Group Scan (TK-3173 only).........................110
21.6 Configuring the Scan ...................................110

21.6.1

Scan Delete/Add.........................................110

21.6.2

Scan List (TK-3173 only) ............................111

21.6.3

Scan List Table (TK-3173 only) ..................111

21.6.4

Priority/ Priority Zone-channel ....................111

21.6.5

Revert CH/GID............................................112

21.6.6

Dropout Delay Time....................................112

21.6.7

Dwell Time ..................................................112

21.6.8

Lookback ....................................................113

21.6.9

Scan Type...................................................113

21.6.10 Revert CH/GID Display...............................113
21.6.11 Priority-channel Stop Tone .........................113
21.6.12 Power-on Scan ...........................................113

22 EMERGENCY MODE ........................... 114

22.1 Configuring Emergency Mode .....................114

22.1.1

Emergency CH/GID Type ...........................115

22.1.2

Emergency Zone-CH/GID...........................115

22.1.3

Emergency Cycle........................................115

22.1.4

Duration of Locator Tone 1 .........................115

22.1.5

Transmit Duration .......................................116

22.1.6

Duration of Locator Tone 2 .........................116

22.1.7

Receive Duration ........................................116

22.1.8

Emergency Display.....................................116

22.1.9

Emergency Text..........................................116

22.1.10 Emergency Mode Type...............................117
22.1.11 Emergency-key Delay Time........................117
22.1.12 Emergency Mic Sense................................117
22.1.13 Emergency ACK Code................................117
22.1.14 Emergency Reset Code..............................117
22.1.15 Emergency Recognition..............................117
22.1.16 Emergency LED..........................................118
22.1.17 Background Transmission ..........................118
22.1.18 Man-down Switch Type ..............................118
22.1.19 Man-down Delay Time................................118
22.1.20 Man-down Pre-alert ....................................118
22.1.21 Man-down Logic Type ................................118
22.1.22 Emergency ID .............................................119
22.1.23 Emergency DTMF ID ..................................119
22.1.24 Emergency Call Fleet .................................119
22.1.25 Emergency Call ID......................................119

23 DATA COMMUNICATION.................... 120

23.1 Data Communication Configuration.............120

23.1.1

Data ............................................................120

23.1.2

Data Zone-CH/GID .....................................120

23.1.3

Data Transmit with QT/DQT .......................120

23.1.4

COM port ....................................................120

24 EXTENDED FUNCTION ....................... 121

24.1 Squelch Logic Signal ...................................121

25 VOX....................................................... 122

25.1 Configuring the VOX Function.....................122

25.1.1

VOX Gain Level ..........................................122

25.1.2

VOX Delay Time .........................................123

25.1.3

Transmit Inhibit while Receiving .................123

25.1.4

Cancel Operation........................................123

25.1.5

VOX Proceed Tone.....................................123

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments