Kenwood TK-2170 SERIES Function Reference Download | Manualshive

Page: 131 / 142

background image

22 EMERGENCY MODE

FUNC (K)/Ver. 1.01

Confidential

119

Configuration using KPG-101D

•

Configuring the Man-down Logic Type (Refer to
FPRG 6.14.21 Man-down Logic Type (Man-
down).)

22.1.22 Emergency ID

The type of control and the code to be sent each time the
transceiver starts an automatic transmission or reception
in Emergency Mode can be configured.
Emergency ID can be configured by KPG-101D. The
following Emergency IDs are available.

Table 22-6 Emergency ID Operation

Note:

ANI Board can be configured only when “ANI Board” is
selected from the

Product Information

window >

Optional

Board

dropdown list.

Configuration using KPG-101D

•

Configuring the Emergency ID (Refer to FPRG
6.14.22 Emergency ID.)

22.1.23 Emergency DTMF ID

The DTMF code sent first in Emergency Mode can be
configured if “DTMF” is selected from the

Emergency ID

dropdown list.
Emergency DTMF ID can be configured by using KPG-
101D.

Configuration using KPG-101D

•

Configuring the Emergency DTMF ID (Refer to
FPRG 6.14.23 Emergency DTMF ID.)

22.1.24 Emergency Call Fleet

The Call Fleet sent first in Emergency Mode can be
configured if “FleetSync” is selected from the

Emergency

ID

dropdown list.

Emergency Call Fleet can be configured by using KPG-
101D.

Configuration using KPG-101D

•

Configuring the Emergency Call Fleet (Refer to
FPRG 6.14.24 Emergency Call Fleet.)

22.1.25 Emergency Call ID

The Call ID sent first in Emergency Mode can be
configured if “FleetSync” is selected from the

Emergency

ID

dropdown list.

Emergency Call ID can be configured by using KPG-
101D.

Configuration using KPG-101D

•

Configuring the Emergency Call ID (Refer to
FPRG 6.14.25 Emergency Call ID.)

Emergency ID

Operation

None

The transceiver transmits and receives
according to the configuration
programmed by using KPG-101D.

DTMF

The transceiver transmits and receives
according to the configuration
programmed by using KPG-101D. The
transceiver first sends the DTMF code
selected from the Emergency DTMF ID
when sending a message in Emergency
Mode.

FleetSync

The transceiver transmits and receives
according to the configuration
programmed by using KPG-101D. The
transceiver first sends the FleetSync
Selcall ID selected from the Emergency
Call Fleet and Emergency Call ID when
sending a message in Emergency Mode.

ANI Board

The transceiver transmits and receives
in conjunction with the ANI Board
control.

«
...
129
130
131
132
133
...
»

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments

Related manuals for TK-2170 SERIES

Brand: Vante Pages: 33

Brand: Jensen Pages: 14

Brand: Coby Pages: 2

Brand: LNI Pages: 42

Brand: Sirius XM RAdio Pages: 26

powerstation go AC

Brand: Mophie Pages: 17

Brand: Philco Pages: 7

Brand: Briggs & Stratton Pages: 5

Brand: Radio Shack Pages: 45

IntelliChlor SCG

Brand: Pentair Pool Products Pages: 12

Brand: ZIPPER MASCHINEN Pages: 151

Brand: Powermate Pages: 40

Bearcat BC148XLT

Brand: Uniden Pages: 23

Brand: Oricom Pages: 29

Brand: Vertex Standard Pages: 40

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 32

DVD LS82 - DVD Player - 8.5

Brand: Panasonic Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands