Kenwood TK-2170 SERIES Function Reference Download | Manualshive

Page: 90 / 142

background image

19 2-TONE

78

Confidential

FUNC (K)/Ver. 1.01

19.3 Decode

There are 3 types of Optional Signaling for each channel
in the Conventional Group: 2-tone 1, 2-tone 2 and 2-tone
3.
The following functions can be configured for 2-tone 1,
2-tone 2 and 2-tone 3:
•

Decoder 1 to Decoder 2

•

A Tone/ B Tone/ C Tone/ D Tone

•

Auto Reset Timer

•

Clear to Transpond

•

Selective Call Alert LED

19.3.1 Decoder 1 to Decoder 2

Two types of Decoders can be configured for 2-tone 1,
2-tone 2 and 2-tone 3. The transceiver can receive the
2-tone code configured for Decoder 1 to Decoder 2 at the
same time.
The following functions can be configured for each
Decoder.

Call Format

Call Format can be used to configure the A Tone, B Tone,
C Tone and D Tone combinations for receiving a call.
Below is a list of the combinations.

Table 19-2 Call Format Combination List

Transpond/ Alert Tone

Transpond/ Alert Tone can be used to configure the
transceiver operation when the transceiver receives a
call with 2-tone.

Table 19-3 Transpond/ Alert Tone Operation

Combination

Combination Pattern

Standby

1

• A-B (The transceiver waits to

receive A Tone and B Tone.)

• A-C (The transceiver waits to

receive A Tone and C Tone.)

• A-D (The transceiver waits to

receive A Tone and D Tone.)

The transceiver
waits to receive
the 1st Tone for 1
second and the
2nd Tone for 3
seconds.

2

• B-A (The transceiver waits to

receive B Tone and A Tone.)

• B-C (The transceiver waits to

receive B Tone and C Tone.)

• B-D (The transceiver waits to

receive B Tone and D Tone.)

3

• C-A (The transceiver waits to

receive C Tone and A Tone.)

• C-B (The transceiver waits to

receive C Tone and B Tone.)

• C-D (The transceiver waits to

receive C Tone and D Tone.)

4

• D-A (The transceiver waits to

receive D Tone and A Tone.)

• D-B (The transceiver waits to

receive D Tone and B Tone.)

• D-C (The transceiver waits to

receive D Tone and C Tone.)

5

• Long A (The transceiver

waits to receive A Tone.)

The transceiver
waits to receive a
Single Tone for
more than 5
seconds.

6

• Long B (The transceiver

waits to receive B Tone.)

7

• Long C (The transceiver

waits to receive C Tone.)

8

• Long D (The transceiver

waits to receive D Tone.)

Transpond

Alert

Operation

No

Off

The transceiver does not
respond.

Alert Tone

or

Ringing Tone

Off

The transceiver transmits the
Transpond tone.

No

Other than Off

The transceiver emits the Alert
Tone.

Alert Tone

Other than Off

The transceiver emits the Alert
Tone after transmitting the
Transpond tone.

Ringing Tone Other than Off

The transceiver emits the
Ringing Tone after transmitting
the Transpond tone.

«
...
88
89
90
91
92
...
»

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments

Related manuals for TK-2170 SERIES

Brand: Samyung ENC Pages: 23

Brand: Teac Pages: 12

Brand: Binatone Pages: 2

Brand: Albrecht Pages: 16

Brand: kchibo Pages: 3

Brand: Albrecht Pages: 13

Brand: PNI Pages: 132

Brand: Subaru Pages: 28

Brand: La Crosse Technology Pages: 22

Brand: C. Crane Pages: 13

Brand: Winco Pages: 36

Brand: BC Pages: 19

Brand: Kirisun Pages: 76

Watchman FDL-22

Brand: Sony Pages: 4

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

ZS-X3CP Marketing Specifications & Features

Brand: Sony Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands