Kenwood TK-2170 SERIES Function Reference Download | Manualshive

Page: 127 / 142

background image

22 EMERGENCY MODE

FUNC (K)/Ver. 1.01

Confidential

115

22.1.1 Emergency CH/GID Type

Configure the CH/GID Type for Emergency Mode.
Emergency CH/GID Type can be configured by using
KPG-101D. Emergency CH/GID Type can be used in the
following way.

Table 22-1 Emergency CH/GID Type Operation

Configuration using KPG-101D

•

Configuring the Emergency CH/GID Type (Refer
to FUNC 6.14.1 Emergency CH/GID Type.)

22.1.2 Emergency Zone-CH/GID

Emergency Zone-CH/GID can be used to configure the
Zone-CH/GID available in Emergency Mode if “Fixed” is
selected from the

Emergency CH/GID Type

dropdown

list.
The transceiver jumps to the Emergency Zone-
CH/GID in the following ways:
•

Pressing the

Emergency

key.

•

The switch that is connected to the Man-down tilt
switch input port is active.

Note:

The transceiver does not decode the Stun Code and
Optional Signaling in Emergency Mode.

Configuration using KPG-101D

•

Configuring the Emergency Zone-CH/GID (Refer
to FPRG 6.14.2 Emergency Zone-CH/GID.)

22.1.3 Emergency Cycle

Emergency Cycle is the number of times to switch
between transmission and reception in Emergency Mode.
Emergency Cycle can be configured by using
KPG-101D. Emergency Cycle activates in the following
way.

Table 22-2 Emergency Cycle Operation

Configuration using KPG-101D

•

Configuring the Emergency Cycle (Refer to FPRG
6.14.3 Emergency Cycle.)

22.1.4 Duration of Locator Tone 1

Duration of Locator Tone 1 is the alert tone beeping
before automatic transmission begins in Emergency
Mode.
This tone sounds when the transceiver alternates
between transmit and receive in Emergency Mode.
A user can easily recognize that the transceiver is about
to transmit the Emergency when the Tone sounds. The
dispatcher can use this tone to locate a user who is in an
emergency situation.
The Duration of Locator Tone 1 can be configured by
using KPG-101D.

Configuration using KPG-101D

•

Configuring the Duration of Locator Tone 1 (Refer
to FPRG 6.14.4 Duration of Locator Tone 1.)

Emergency

CH/GID Type

Operation

Selected

The transceiver transmits or
receives using the selected
CH/GID when the transceiver enters
Emergency Mode.

Fixed

The transceiver jumps to the Zone-
CH/GID configured in Emergency
Zone-CH/GID and begins
transmitting or receiving when the
transceiver enters Emergency
Mode.

Emergency Cycle

Operation

1 to 200

The transceiver repeats automatic
transmission start tone

automatic

transmission

automatic

transmission end tone

automatic

reception for configured number of
times and exits from Emergency
Mode.

Infinite

The transceiver alternates between
transmit and receive until the

Emergency

key is pressed or the

transceiver is turned OFF.

«
...
125
126
127
128
129
...
»

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments

Related manuals for TK-2170 SERIES

Brand: PURE Pages: 148

ATS-909X - WORLD BAND RADIOS

Brand: Sangean Pages: 1

Brand: Sangean Pages: 24

Brand: Sangean Pages: 96

Brand: Sandstorm Pages: 208

Twintalker 7100

Brand: Topcom Pages: 22

Brand: Grundig Pages: 75

Satellite Radio

Brand: Raritan Pages: 2

Brand: Baldor Pages: 1

Brand: Troy-Bilt Pages: 12

Brand: Yaesu Pages: 32

Brand: Champion Pages: 28

Brand: Kongsberg Pages: 74

Brand: Curtis Pages: 21

Brand: Troy-Bilt Pages: 28

Brand: CYP Pages: 16

ISM BAND XYR 5000 LINE

Brand: Honeywell Pages: 49

Brand: Honeywell Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands